Pb Scanner

[rjcb]

Salut,

J'ai installé une imprimante sous ma FC4. (HP PSC 1610 multifonctions)

Je précise que le scanner a déja fonctionner avec la meme config mais comme j'ai tous refais sur ma FC4 je passe par la.

La aucun pb. Par contre je voudrais pouvoir scanner: donc j'ai suivi ceci

http://www.bawet.org/article.php3?id_article=48

et j'ai essayer la deuxième méthode .

J'ai installer tout les packages

Dans le ficiher dll.conf de saned, j'ai décommenter hpoj

Dans le configurateur impression, j'ai séléctionné

ptal:/mlc:USB:PSC_1600 SERIES.

Puis:

[root@RJCSERVEUR ~]# /usr/sbin/ptal-init setup

Stopping the HP OfficeJet Linux driver.

----------------------------------------------------------------------

This program manages devices controlled by the HP OfficeJet Linux

driver (hpoj). It attempts to probe your computer for local parallel-

and USB-connected devices, and allows you to specify network addresses

for remote JetDirect-connected devices.

If you experience any difficulties in detecting your device(s), then

refer to the hpoj documentation for troubleshooting information.

----------------------------------------------------------------------

Currently defined device names ([*]=default):

"mlc:usb:PSC_1600_series"

Model is "PSC 1600 series".

Serial number is "HU55DDR2HXL0".

Press <Enter> alone to continue, or if you would like to delete

or reconfigure one of the above-listed devices, then enter the

device name to delete here --->

----------------------------------------------------------------------

Probe for parallel-connected devices ([y]/n)? n

----------------------------------------------------------------------

Probe for USB-connected devices ([y]/n)? y

Probing "/dev/usb/lp0"...

Found "PSC 1600 series"

with serial number "HU55DDR2HXL0".

This device is already set up as "mlc:usb:PSC_1600_series".

Probing "%002%001"...

No device found.

Probing "%001%002"...

No device found.

Probing "%001%001"...

No device found.

----------------------------------------------------------------------

Press <Enter> alone to continue, or if you would like to add a

JetDirect-connected device, then enter its dotted-decimal

IP address or hostname here --->

----------------------------------------------------------------------

Done updating device configuration files stored under /etc/ptal.

If you make manual changes to those files, then be sure to run

"/usr/sbin/ptal-init start" so they will take effect.

----------------------------------------------------------------------

Starting the HP OfficeJet Linux driver.

mlc:usb:PSC_1600_series

[root@RJCSERVEUR ~]# /usr/sbin/ptal-init start

[root@RJCSERVEUR ~]#

[root@RJCSERVEUR ~]# sane-find-scanner

# No SCSI scanners found. If you expected something different, make sure that

# you have loaded a SCSI driver for your SCSI adapter.

# Also you need support for SCSI Generic (sg) in your operating system.

# If using Linux, try "modprobe sg".

found USB scanner (vendor=0x03f0 [HP], product=0x4811 [PSC 1600 series]) at libusb:001:002

# Your USB scanner was (probably) detected. It may or may not be supported by

# SANE. Try scanimage -L and read the backend's manpage.

# Not checking for parallel port scanners.

# Most Scanners connected to the parallel port or other proprietary ports

# can't be detected by this program.

[root@RJCSERVEUR ~]#

[root@RJCSERVEUR ~]# scanimage -L

No scanners were identified. If you were expecting something different,

check that the scanner is plugged in, turned on and detected by the

sane-find-scanner tool (if appropriate). Please read the documentation

which came with this software (README, FAQ, manpages).

[root@RJCSERVEUR ~]#

J'ai aussi le choix entre différent drivers pr l'imprimante:

PSC 1600 hpijs (ppd) ou PSC 1600

mon ficihier hp.conf (car la printer est de la marque hp)

#scsi HP

# Uncomment the following if you have "Error during device I/O" on SCSI

# option dumb-read

#

# The usual place for a SCSI-scanner on Linux

#/dev/scanner

#

# USB-scanners supported by the hp-backend

# HP ScanJet 4100C

usb 0x03f0 0x0101

# HP ScanJet 5200C

usb 0x03f0 0x0401

# HP ScanJet 62X0C

usb 0x03f0 0x0201

# HP ScanJet 63X0C

usb 0x03f0 0x0601

# HP ScanJet PSC

usb 0x03f0 0x4811

#

# Uncomment the following if your scanner is connected by USB,

# but you are not using libusb

/dev/usb/scanner0

option connect-device

La je ne sais pas trop les 2 lignes si je dois les décommenter ou pas.

Merci de votre aide

[ggbce]

D'après moi les lignes que tu as activé sont correctes, c'est plutot sane qui ne semble pas supporter le scanner que tu as. En tout cas il n'est pas dans la liste hp-backend.

[rjcb]

Salut!

En fait j'avais oublié la libraire libsane.

Merci