Marcelou Posté(e) le 10 mai 2006 Partager Posté(e) le 10 mai 2006 Bonjour, J'ai un imprimante Canon IP2000 et je ne peux plus imprimer car elle m'affiche le message d'erreur suivant "Le réservoir d'encre usagé est plein" et le voyant de l'imprimante clignote huit fois ! J'ai réinstallé les nouveaux drivers, remis les anciens rien n'y fait ! Est ce que ce réservoir existe vraiment, si oui comment le changer ! Merci d'avance Lien vers le commentaire Partager sur d’autres sites More sharing options...
herfill Posté(e) le 10 mai 2006 Partager Posté(e) le 10 mai 2006 Bonjour, J'ai un imprimante Canon IP2000 et je ne peux plus imprimer car elle m'affiche le message d'erreur suivant "Le réservoir d'encre usagé est plein" et le voyant de l'imprimante clignote huit fois ! J'ai réinstallé les nouveaux drivers, remis les anciens rien n'y fait ! Est ce que ce réservoir existe vraiment, si oui comment le changer ! Merci d'avance Voila un peu de recherche tu vas sur cette page https://self-service.canon-europe.com/fr/pages/ et a gauche tu cliques sur "vous ne trouvez pas la reponse" apres a toi de jouer Lien vers le commentaire Partager sur d’autres sites More sharing options...
FredB Posté(e) le 10 mai 2006 Partager Posté(e) le 10 mai 2006 c'est une jet d'encre ou une laser ? quoi qu'il en soit, y a pas un réservoir qui récupe l'encre lors de nettoyage de têtes ou un truc du genre ? Lien vers le commentaire Partager sur d’autres sites More sharing options...
Einstein-Rosen-Podolsky Posté(e) le 3 février 2007 Partager Posté(e) le 3 février 2007 J'ai le même problème avec ma PIXMA MP110 de canon "Imossible d'imprimer, le réservoir d'encre usagée est plein, remplacé le !" Mais où se situe-t-il et comment on l'enlève pour le remplacer !!!! Merci Lien vers le commentaire Partager sur d’autres sites More sharing options...
K-Lee Posté(e) le 3 février 2007 Partager Posté(e) le 3 février 2007 34 secondes de recherche sur le site de Canon L'absorbeur de résidus d'encre (le réservoir d'encre usagée) est une pièce de l'imprimante qui sert à absorber les résidus d'encre produits lors de certaines opérations telles que le nettoyage de la tête d'impression. Si cette erreur se produit, vous devez remplacer l'absorbeur de résidus d'encre (le réservoir d'encre usagée) et inspecter l'imprimante. Il doit donc se trouver quelque part sous les cartouches. Lien vers le commentaire Partager sur d’autres sites More sharing options...
Einstein-Rosen-Podolsky Posté(e) le 3 février 2007 Partager Posté(e) le 3 février 2007 34 secondes de recherche sur le site de Canon L'absorbeur de résidus d'encre (le réservoir d'encre usagée) est une pièce de l'imprimante qui sert à absorber les résidus d'encre produits lors de certaines opérations telles que le nettoyage de la tête d'impression. Si cette erreur se produit, vous devez remplacer l'absorbeur de résidus d'encre (le réservoir d'encre usagée) et inspecter l'imprimante. Il doit donc se trouver quelque part sous les cartouches. Tu as l'air de t'y connaitre ! Combien çà me couterait de le remplacer par moi-même (si des fois que j'arrive à le trouver) ? et par 1 technicien de canon ? Je présume que l'on doit démonter l'imprimante ! Lien vers le commentaire Partager sur d’autres sites More sharing options...
K-Lee Posté(e) le 3 février 2007 Partager Posté(e) le 3 février 2007 En fait j'ai une canon et je suis en train de me dire que j'espère ne jamais avoir ce problème Parce que je n'ai absolument aucune idée d'où peut bien se situer ce réservoir... Lorsque sur le site de canon j'ai tapé "reservoir d'encre usagé" je suis tombé sur le quote que j'ai posté, mais en dessus de cette phrase il y avait un bouton pour contacter le service technique de Canon, sûrement par mail, donc fais la manip et demande l'assistance d'un technicien, ça ne coûte rien. Je me demande si ce genre de manipulation ne serait pas indiquée dans le manuel de l'imprimante, à regarder donc. Attention les yeux, pompé de Hardware.fr 1 - MISE AU POINT SUR LE COMPTEUR D'ENCRE USAGEE: J'ai démonté totalement ma i560, et il me semble important de faire la mise au point suivante. Pour ce qui est du réservoir d'encre usagée, l'endroit où repose la tête au repos (au moins sur la i560, et aussi sur d'autres), n'est PAS le réservoir d'encre usagée, c'est juste un support, poreux (genre pierre ponce, mais en plastique), sous lequel on trouvent 2 tuyaux (un pour le noir et un pour la couleur) qui eux conduisent au vrai réservoir, qui se trouve au fond de l'imprimante. Ce "réservoir" est en fait le fond de l'imprimante, il est rempli de 3 couches de matière absorbante, genre feutre, mais c'est de la cellulose (ça doit être la même matière que les couches pour bébé) chacune de ces "éponges" mesure 5mm de haut et couvre tout le fond de l'imprimante excepté l'alim, par contre il n'y a aucun capteur pour mesurer soit le niveau de liquide, soit l'humidité. Fond d'une BJC 6000, en cadré en rouge le feutre appelé "réservoir d'encre usagée": (A l'origine, imprimante neuve, tout ce qui y est vert est blanc) http://img484.imageshack us/img484/8256/pad6ou.th.jpg Photo 1 En fait il y a un compteur, et ce compteur totalise le nombre de nettoyages des têtes qui ont été effectués, une fois arrivé au nombre fatidique l'imprimante se bloque. Ceci ne signifie en rien que le "réservoir" soit plein, juste qu'il pourrait l'être. Un exemple au hasard, moi et mon i560 , les "couches" étaient tout de même bien imprégnées mais auraient pu absorber encore le même volume d'encre. Donc quand l'imprimante annonce réservoir d'encre usagée plein, c'est qu'on est arrivé au maxi du nombre de nettoyage de têtes autorisé, et là l'imprimante envoie un msg d'erreur et se bloque. La seule façon de s'en sortir c'est de remettre à zéro ce compteur, la manip est différente selon le type de l'imprimante. En conclusion, il ne faut pas abuser du nettoyage de têtes via le soft d'impression, perso je dirais qu'il ne sert qu'à nettoyer la surface des têtes (par exemple en cas de papier pelucheux) mais que pour déboucher les buses il vaut mieux faire tremper sa tête. Donc si votre impression commence à se détériorer essayez UN et UN SEUL nettoyage de têtes via le soft d'impression, et si le problême n'est pas résolu il est inutile d'insister, de faire tourner le compteur et gaspiller de l'encre, passez à la méthode trempage. Ci-dessous vous trouverez des méthodes et liens pour remettre à zéro le compteur du "réservoir", par contre ceci comporte un risque, ce risque c'est qu'un jour, rassurez vous il y a de la marge, le feutre soit effectivement plein, gorgé d'encre, à ce moment là l'encre risque de couler sur votre beau bureau tout neuf. Au paragraphe 3 ci-dessous vous trouverez la méthodologie pour nettoyer ces feutres. 2 - METHODES DE REMISE A ZERO DU COMPTEUR D'ENCRE USAGEE POUR IMPRIMANTES CANON (en cours de traduction, mise en forme) TOUTES CES PROCEDURES NE SONT PAS DE VAGUES ELUCUBRATIONS DE BIDOUILLEURS, CE SONT DES EXTRAITS DES MANUELS D'ENTRETIEN DES IMPRIMANTES, ELLES SONT UTILISEES QUOTIDIENNEMENT PAR LES REPARATEURS AGREES CANON. Donc si ça ne marche pas chez vous c'est que vous n'avez pas respecté scrupuleusement les divers points de ces méthodes. Les feedbacks sont les bienvenus afin de mettre à jour cette liste de procédures. Pour certains modèles, dont au moins les S900 et i960, il faut d'abord retirer la tête avant de réaliser la procédure. MINI LEXIQUE: Power button = bouton d'alimentation Resume button = bouton Reprendre/Annuler Power Off = éteindre Power On = allumer Hold ou Hold on = maintenir appuyé, en gardant le doigt dessus Press = appuyer juste une impulsion Release = relacher Once= une fois Twice = 2 fois Both = les 2 Steady = allumé de façon permanete pour un voyant Flash = clignote pour un voyant Canon GENERIC "S" SERIES RESET CODE Waste Ink Counter Reset. (1) Turn off the printer. (2) Press and hold the RESUME button, then press and hold the POWER button. (3) Release the RESUME button, Next press and release the RESUME button two(2) more times in succession. Note: you are still holding the POWER button). The printer's carriage will "reset" or move momentarily. If the above was properly performed the printer will enter the "Service Mode". (4) Press the RESUME button 4 times, this will select the clear waste ink counter function. The lamp will alternate (change) color with each key press. 1. Service/Factory test printout, including ink sensor check. 2. EEPROM - Info printout. 3. EEPROM - Initialization. 4. Reset the Waste ink counter. 5. Printer model setting. (More selections beyond this point - However it is best leave them unaltered - You have been warned!) After selecting the desired mode (eg 4), press the POWER button to "set" the change, and return to the top of the function selection menu. Press the POWER button again to restart the printer. ++++++++++ Canon i250 (Merci à Gubew et à Manuec) 1 eteindre l'imprimante et débrancher le cable d'alimentation 2 tenir enfoncé le bouton d'allumage (jusqu'a la fin) et rebrancher le cable d'alimentation 3 la diode doit être verte 4 appuyer et relacher le bouton éjection feuille (resume) la diode doit être orange 5 appuyer le bouton éjection feuille (resume) la diode doit être verte 6 relacher les 2 boutons mon ordinateur a détécté un nouveau matériel et tout est rentré dans l'ordre. ++++++++++ Canon i320, i255 Waste Ink Counter Reset. Step 1 : Manual Temporary Only 1. Unplug power and USB. 2. Open door and hold power button. 3. Connect power. 4. Close door, then release power button. For Reset by software or Step 1: Manual for service mode 1. Turn off the printer. And disconnect the printer cable. 2. Press and hold the POWER button, turn on the printer. 3. The indicator (L.E.D.) should be green. 4. Press and release the RESUME button , the indicator (L.E.D.) should be orange. 5. Press and release the RESUME button again, the indicator (L.E.D.) should be green. 6. Release both buttons. step 2 : Software for Permanant 1. Reconnect the printer cable. 2.Open General Tools software and select (USB PORT) 3 .Choose (SET DESTINATION 1) And it should be reset. Remark "After service mode Pls use software for permanent reset" ++++++++++ Canon PIXMA IP1000, IP 1500 Waste Ink Counter Reset. Step 1: Manual for Service mode 1. Turn off the printer. And disconnect the printer cable. 2. Press and hold the POWER button, turn on the printer. 3. The indicator (L.E.D.) should be green. 4. Press and release the RESUME button , the indicator (L.E.D.) should be orange. 5. Press and release the RESUME button again, the indicator (L.E.D.) should be green. 6. Release both buttons. step 2 : Software for Permanant 1. Reconnect the printer cable. 2.Open General Tools software and select (USB PORT) 3 .Choose (SET DESTINATION 1) And it should be reset. Remark "After service mode Pls use software for permanent reset" ++++++++++ Canon i850, i950, S600 Start with the printer OFF 1. Hold down RESUME and then hold down POWER 2. release RESUME 3. press RESUME twice, then release POWER 4. Let green light blink until printer is done futzing Select function with RESUME press POWER to execute: presses - light color - function Number of presses - light color - function 0 presses - green - Test print (or exit service mode on i960) 1 press - orange - EEPROM info print (plus grid nozzle diagnostic on i960) 2 presses - green - EEPROM initialize 3 presses - orange - Reset waste ink counter ++++++++++ i965 (Merci à Boularan) 1/ ETEINDRE 2/ APPUYER SUR EJECTION ET MAINTENIR 3/ APPUYER ET MAINTENIR MISE EN ROUTE (POWER) 4/ APPUYER 1 FOIS SUR EJECTION (RESUME) LE LED DEVIENT ORANGE APPUYER 1 DEUXIEME FOIS ET IL DEVIENT VERT 5/ VOUS ETES (peut être) EN MODE SERVICE 6/ RELACHER MISE EN ROUTE CA PASSE AU VERT ET LE CHARIOT BOUGE ATTENDEZ QUE CA SE CALME ET QUE CA REPASSE AU VERT fixe 7/ APPUYEZ 4 FOIS SUR EJECTION POUR REMETTRE LE COMPTEUR A ZERO . Le led passe alternativement du vert à l'orange 8/ APPUYER SUR MISE EN ROUTE (peut être plusieurs fois) POUR ETEINDRE Ensuite vous allez tester si le miracle s'est produit ++++++++++ Canon S450 Printer 1: Power off printer 2: Hold Resume button then press and hold POWER, the beeper will sound once. 3: Hold POWER and release RESUME 4: Press RESUME twice 5. Release Power button 6: When the indicator lights steady, press RESUME three(3) times. The indicator should be orange. 7: Press Power to set data ++++++++++ Canon BJC 1000 Serie 1: Remove Cartridge 2: Unplug the AC Power Cord 3: Hold down the RESUME button 4: Release RESUME after plugging in the AC Power cord. 5: Press the RESUME once within 5 seconds and release the RESUME . 6: Press and HOLD RESUME for two seconds or more and release it. 7: Press and HOLD RESUME for two seconds or more and release it. 8: Unplug AC Power Cord to set data. ++++++++++ Canon BJC-2000 BJC-2100 Serie 1: Remove the Cartridge 2: Unplug the AC Power Cord 3: Close Front access panel 3: Hold down the RESUME/RESET button and plug in the AC power cord 4: Release RESUME/RESET after plugging in the AC Power cord. 5: Press the RESUME/RESET once within 5 seconds and release the RESUME/RESET . 6: Press and HOLD RESUME/RESET for two seconds or more and release it. 7: Press and HOLD RESUME/RESET for two seconds or more and release it. 8: Unplug AC Power Cord to set data. ++++++++++ Canon BJC-210 BJC-240 BJC-250 BJC-255 BJC-265 Canon BJC-4100 BJC-4200 BJC-4300 BJC-4400 BJC-4550 BJC-4650 Unplug Power Cord Hold POWER and RESUME buttons Plug in Power Cord Release buttons Open front door of printer Hold the CARTRIDGE and RESUME buttons Press POWER Release all buttons after the beeps Press CARTRIDGE once Press RESUME ++++++++++ Canon BJC-5000 1: Power off printer 2: Press and hold RESUME then press POWER, The indicator will start blinking. 3: While the indicator is blinking , Press RESUME twice then Wait until the printer beeps to indicate service mode 5: When the indicator lights steady GREEN, press RESUME four(4)times. The indicator should be GREEN. 6: Press Power to set data Service Test Print 1: Power off printer 2: Press and hold RESUME then press POWER, The indicator will start blinking. 3: While the indicator is blinking , Press RESUME twice then Wait until the printer beeps to indicate service mode 5: When the indicator lights steady GREEN, press RESUME two(2)times. The indicator should be GREEN. 6: Press Power to Print Nozzle Print 1: Power off printer 2: Press and POWER, until the printer beeps and release. Demonstration Print 1: While the printer in ON , , Press and hold RESUME until the printer plays a melody of beeps. ++++++++++ Canon BJC-5100 Self Test Switch Printer off. Hold Power for 1 beep. Waste Counter Reset 1: Power off printer 2: Press and hold RESUME then press POWER, The indicator will start blinking. 3: While the indicator is blinking , Press RESUME twice then Wait until the printer beeps to indicate service mode 5: When the indicator lights steady GREEN, press RESUME four(4)times. The indicator should be GREEN. 6: Press Power to set data Service Test Print 1: Power off printer 2: Press and hold RESUME then press POWER, The indicator will start blinking. 3: While the indicator is blinking , Press RESUME twice then Wait until the printer beeps to indicate service mode 5: When the indicator lights steady GREEN, press RESUME two(2)times. The indicator should be GREEN. 6: Press Power to Print Nozzle Print 1: Power off printer 2: Press and POWER, until the printer beeps and release. Demonstration Print 1: While the printer in ON , , Press and hold RESUME until the printer plays a melody of beeps. ++++++++++ Canon BJC-3000 BJC-6000 BJC-6100 BJC-6200 S400 S450 F300 F600 F620 Canon BJC-7000 BJC-7100 BJC-8000 BJ-F800 i6500 Waste Reset 1: Power off printer 2: Hold Resume button then press and hold POWER, the beeper will sound once. 3: Hold POWER and release RESUME 4: Press RESUME twice then release BOTH POWER and RESUME buttons 5: When the indicator lights becomes steady, press RESUME three(3) times. The indicator should be ORANGE. 6: Press Power to set data Model Type reset 1: Power off printer 2: Hold Resume button then press and hold POWER, the Green Indicator will light. 3: Hold POWER and release RESUME 4: Double click RESUME then release BOTH POWER and RESUME. 5: Press resume 4 times, Green Indicator should be lite. 6: Press POWER to enter the MODEL setting mode. 7: if the indicator is GREEN this is BJ-F620 to Set BJC-6200, press RESUME 1 time , the indicator should be ORANGE. 8: Press POWER to save ++++++++++ Canon BJC-600 BJC-600e BJC-610 BJC-620 1: Unplug Power Cord 2: Hold POWER and FF and Print Mode buttons 3: Plug in Power Cord 4: Release after the beeps ++++++++++ Canon BJC-50 BJC-55 BJC-80 BJC-85 M40 M70 1: Unplug Power Cord 2: Hold POWER and RESUME buttons 3: Plug in Power Cord 4: Release buttons after the printers starts up 5: Hold CARTRIDGE and RESUME 6: Press POWER 7: Release all buttons after the beeps 8: Press CARTRIDGE 16 times 9: Press RESUME 10: Unplug the Power cord +++++++++ Canon BJ-30 BJC-35v BJC-70 F14 Error Reset 1: Unplug adapter 2: Hold POWER 3: Plug in ADAPTER 4: Release POWER after printer starts 5: Hold FF and MENU and press POWER 6: Release after beeps 7: Press <> Cartridge until 1A is displayed 8: Press ONLINE 9: Press POWER to shutoff printer 10: Unplug printer then re-plug printer ++++++++++ Canon BJ F900, F890, F700, F500, S900, S820, S750 and S520 Turn off the printer. Press and hold the RESUME button, then press and hold the POWER button. Release the RESUME button, then press and release the RESUME button two more times in succession. (youre still holding the POWER button during this). The printer mechanics will move momentarily. You are now in Service mode. Pressing the RESUME key will select a function; for example, pressing RESUME 4 times will select the clear waste ink counter function. The lamp will alternate color with each key press. 1. service/factory test printout, including ink sensor check 2. EEPROM info printout 3. EEPROM initialization 4. Clear the waste-ink counter 5. Printer model setting. (more selections beyond this- leave this alone) After selecting mode, press the POWER button to commit the change, and return to the top of the function selection menu. Pressing the POWER button again turns off the printer for a resta ++++++++++ Canon S9000, S300, S400, i550, i560, i850, i860, i865, i9100, i9950, PIXMA IP3000, IP2000, 1. Turn off printer 2. Hold down Resume button and press Power button. 3. Keep holding down Power button and let Resume button go. 4. Press Resume button 2 times then let BOTH buttons go. 5. Green lights will flash and then stop blinking. 6. When green lights are solid, press the Resume button 4 times. 7. Press the Power button and the printer should turn off, if not, press the Power button once more. 8. Your printer should respond as normal. +++++++++ Canon S900, S820, S750, S520 Turn off the printer. Press and hold the RESUME button, then press and hold the POWER button. While still holding the POWER button, Release the RESUME button, then press and release the RESUME button two more times in succession. The printer mechanics will move momentarily. You are now in Service mode. Release the Power Button. Pressing the RESUME key will select a function; for example, pressing RESUME 4 times will select the clear waste ink counter function. The lamp will alternate color with each key press. 1. Service/factory test printout, including ink sensor check 2. EEPROM info printout 3. EEPROM initialization 4. Clear the waste-ink counter 5. Printer model setting. (more selections beyond this- leave this alone) After selecting mode, press the POWER button to commit the change, and return to the top of the function selection menu. Pressing the POWER button again turns off the printer for a restart. ++++++++++ Canon S9000 Turn off printer Hold down Resume button and press Power button. Keep holding down Power button and let Resume button go. Press Resume button 2 times then let BOTH buttons go. Green lights will flash and then stop blinking. When green lights are solid, press the Resume button 4 times. Press the Power button and the printer should turn off, if not, press the Power button once more. Your printer should respond as normal. +++++++++ Canon MPC 190 / MPC 200 Reset Waste Ink 1) Enter SERVICE MODE. By pressing Menu, Copy, Scan, Copy, Copy 2) Select TEST MODE. 3) Select [8] PRINTER TEST in TEST MODE. 4) Select 3. [EEPROM CLEAR]. 5) Select 0. [iNK COUNT]. 6) Press the [set] key. 7) Press the [stop/Reset] key (returning to the state of 3)), and then press the [ON/OFF] key ++++++++++ Canon MP 370 1) Printer on, press Additional Functions, Scan, Copy, Scan. Now you should be in service mode from there for waste ink tank reset it is simalar to what has already been posted 2) Select Test mode which is like the last available selection 3) Select #8 Printer Test, it will do something here like cleaning or something then it will come up with some other option this is where it gets a bit confusing cause now all it says is like 8-2 or 8-3 push the + or - button until it says 8-3 then hit the select button 4) The menu will now say EEPRON Clear. Select Ink count which is option (0) and press set 5) Select Ink count which is option (0) and press set. +++++++++++++++++++ Canon MP 400/MP 730/MP 600 1) Enter SERVICE MODE.--- By pressing Menu-Copy-# 2) Select TEST MODE. 3) Select [8] PRINTER TEST in TEST MODE. 4) Select 3. [EEPROM CLEAR]. 5) Select 0. [iNK COUNT]. 6) Press the [OK] key. 7) Press the [stop/Reset] key (returning to the state of 3)), and then press the [ON/OFF] key. +++++++++++++++++++ Canon MPC 400 / MPC 600 Erreur ##343 1. Go to menu by pressing the > button 2. press [copy] and then # 3. go to 'test mode' by pressing > several times 4. press "OK" 5. now press 8 then 3 then 0 6. After that press the on/off button, everything should be fine now. +++++++++++++++++++ Canon MP730 1. Hit the "menu": Key 2. Hit "Copy" Key 3. Hit "#" Key 4. Scroll thru the menu headings until you come to "Test Mode" - 12th heading 4a. Hit "8" to select Printer Test 5. Hit the "3" button- this will bring up Eprom Clear 6. Hit "0" button 7. Hit the "Stop" button After completion of step 7, turn printer off and On again to set the new settings Toutes ces infos proviennent des sites suivants: http://www.neilslade.com/Papers/inkjetstuff11.html http://www.cyber-ink.com/member-canon.html 3 - NETTOYAGE DES FEUTRES: Avant de vous lancer dans cette manip lisez bien tout ce topic, et surtout consultez les liens où il est expliqué comment démonter une imprimante. Une fois le compteur remis à zéro c'est comme si on roulait sur la réserve du réservoir d'essence d'une voiture, on peut encore rouler, mais pas 500Km. Donc après avoir remis ce compteur à zéro, quand je dis après, il n'y a pas urgence, mais pensez à le faire, il vous faudra démonter votre imprimante. Habillez-vous en dégueulasse, une giclée d'encre est vite arrivée Toutes les Canon sont faites de 3 parties, le dessus de la coque, la partie imprimante (rouleau, tête, électronique etc) et le fond partie basse de la coque. Démonter la coque est assez délicat vu qu'elle est clipsée et non vissée, mais en faisant ça avec soin c'est possible. Pour sortir la partie imprimante il y a des vis à dévisser, et aussi des fils ou des nappes (juste 2 ou 3) à débrancher, pour les fils/nappes c'est simple il y a toujours des connecteurs, rien à déssouder Vous trouverez ci-dessous des liens avec photos expliquant comment démonter certains modèles. Une fois démontée il faut emmener toute la partie basse (le fond de l'imprimante qui contient les feutres) dans une baignoire ou un évier, ces feutres sont gorgés d'encre, et ça tache !!! Extraire les feutres en repérant bien leur ordre, il y a en 2 ou 3 ou 4 selon les modèles, chacun de forme différente, mettre le fond de l'imprimante à l'abri, hors de la baignoire ou évier. On arrive au sérieux, on prend les feutres un par un, puis on les presse afin d'en faire sortir l'encre, ne pas presser trop fort tout de même, passer un coup de douchette à l'eau chaude, puis re-presser, puis re-douchette, re-presser etc ....... jusqu'à ce que le liquide sortant du feutre soit clair. On laisse sècher les feutres (en été les miens ont séché en 24h) sur un séchoir. On peut accélérer le séchage en les passant au sèche cheveux au début. Une fois qu'ils sont bien secs il faut les secouer, les tapoter, pour leur redonner du volume. Il ne vous reste plus qu'à les replacer dans le socle de l'imprimante et à tout remonter. 4 - DES LIENS INTERESSANTS: LE site d'où j'ai tiré le principal des procédures: http://www.printersiam.com/data/Ca [...] edures.htm Topic en français sur les BJC: http://www.commentcamarche.net/for [...] ote-orange Forum sur les jet d'encre (en anglais): http://www.fixyourownprinter.com/forums/inkjet Section du même forum sur le réservoir d'encre usagé plein (en anglais): http://www.fixyourownprinter.com/f [...] t/15284#65 Un forum sur les jet d'encre (en anglais): http://www.nifty-stuff.com/forum/viewforum.php?id=2 Forum d'un site commercial (en français): http://sosimprimante.com/index.php?act=idx Page perso où il est expliqué comment démonter une BJC3000 (en anglais): http://mysite.wanadoo-members.co.u [...] onBJC.html Page perso où il est expliqué comment démonter une BJC6500 (en anglais mais beaucoup de photos): http://www.sitemaster-internet.co.uk/bjc6500/index.htm Lien vers le commentaire Partager sur d’autres sites More sharing options...
Messages recommandés
Archivé
Ce sujet est désormais archivé et ne peut plus recevoir de nouvelles réponses.